How To Connect Xvim Cameras To Phone

Here are few of a problems that occurred most of the time while using xvim camera, therefore to ensure that user will not face these problems in the future and a particular xvim camera troubleshooting confronting them are listed beneath.

List of Xvim Camera Troubleshooting

Xvim Camera Non Recording

Misconfiguration, lack of storage chapters, and malfunctioning DVR components are major explanations if your CCTV photographic camera is working fine only the DVR is not recording annihilation. Don't worry: today'due south DVR units are user-friendly and simple to troubleshoot.

Make sure that recording is turned on. It may seem self-evident, yet information technology occurs. The DVR box may stop recording without your knowledge if you lot return a device to its factory settings, or if the settings became damaged and were automatically returned to factory defaults.
Check your CCTV and DVR settings to make sure that recording is turned on permanently, or at to the lowest degree for the time you're troubleshooting. Some devices may be fix to exclusively capture footage at specific intervals.
Make certain your DVR'due south recording media has plenty storage capacity. Remove whatsoever video that y'all don't require.
Check the network connections of your DVR if it uploads footage to a network server or a cloud account. Information technology's possible that its local storage is full.
The hard drive in your DVR might be deteriorating. Because many DVRs comprise a express on-board Wink storage for their software and solely use the hard drive for recording, your DVR may continue to operate even if it tin no longer save footage.

Xvim CCTV non working on mobile

If you tin't see your CCTV on your mobile device, information technology's because your Internet Router (WiFi) isn't delivering an net connexion to your CCTV Recorder (DVR / NVR). At that place might be a number of causes for this, so please start past identifying the app you lot're using from the list below.

Video Surveillance Ivideon
XVR Pro

Once you are certain nearly the setup is done with zippo error then go downwards the listing and run into how you can troubleshoot this problem, nonetheless a complete setup is in detailed beneath.

Cheque the cyberspace connection is actually working at habitation / businesses offset. Can you connect to your Wi-Fi? Can you lot load internet pages?
If the connectedness betwixt the router (internet Wi-Fi) and recorder (DVR/NVR) is hard wired, so please reboot both your router and your CCTV offset and check again.
If you are using the TP Link Powerline Adapters then please ensure that the adapters are displayingthree green lights on them. If the adapters display two or less lights the connexion volition not work. This unremarkably happens during a power surge or spike. To rectify this, you will need to turn off the TP Link Plug from the mains switch, count to v – so turn it back on. You lot should then come across three green lights on the plugs, thus restoring the internet connexion to your CCTV.
Does your phone receive an internet signal? Is it connected to Wi-Fi or 4g?
If the in a higher place is all correct, and your app is nonetheless showing the device as 'offline', please refresh your app by dragging down with your finger the camera list view. This volition update the feed inside your app.
If you checked all of the above and are confident the issue it non with your cyberspace, then please contact their back up via email and log a ticket.

How to connect XVIM CCTV Camera to Mobile?

After downloading app via from QR Code or download directly as listed above.

The system setup with the cameras were super piece of cake. Setting up the mobile app was easy also. The difficult function was setting up email and remote access.

Things you need to do, setup Email, Phone App and Remote Access:

Network

Then straight Connect the DVR with a patch cable to a Modem.
Enable DHCP on DVR and Examination Network.

Electronic mail

You lot have to create another Gmail account so you could setup the email choice.
Under Email, Enable, Select My SMTP server, Gmail was port 465 (yous have to research that)

Selected SSL

Username keyed in the new email address and new password
Sender will exist your original Gmail account
Receiver is whomever you want to receive the warning.

Deject

Enabled Cloud service
Went to App store and scanned the Android (depends on your telephone) and installed the XVRView app to my phone.
Open up XVRView app, add together new device and scan the Remote Access bar code
In the app, selected local, bill of fare, Plus sign and add together your device

Remote access DVR settings

Select Network and notation the HTTP and Mobile ports
Select Cyberspace Service and notation the RTSP port and enable RTSP

Modem configuration

Remote into your Router and select advanced and Port Forwarding (Modems differ with Make and Model)
Add the ports for the above-mentioned ports for both TCP and UDP